My 65 [Archive] - GermanLook Forums

View Full Version : My 65

Fast65

September 12th 2010, 14:18

Hi

my cars not german look or Cal Look but has bits of both some of you may have seen my car on other forums so fingers crossed not to boring lol

Specs so far

Engine

2332 turbo, efi, NOS, water injected, charge cooled T1

Transmission

T1 pro street

Wheels

OG Bruners

Brakes

944 Turbo with 928 4 pots

Interior

70s 911 tombstones and a few gauges :D

ive done all the work on the car myself starting from this

Ok i purchased this bug for my wife in 2007 and looked like this

http://i71.photobucket.com/albums/i149/gluemixer/heidi3.jpg

i wanted her to stay like this but claire wanted me to lower her so she then looked like this

http://i71.photobucket.com/albums/i149/gluemixer/DSC00080.jpg

so that was it the car has been messed with so i took this out

http://i71.photobucket.com/albums/i149/gluemixer/DSC00430.jpg

and put this in

2332cc CB high roof case, Scat crank 84mm, CB H beam rods, 94mm B+P, Total seal rings, Engle FK10 cam, Scat lifters, Berg chromoly pushrods, Jaycee pushrod tubes, Scat 1.4 rockers, A1 1 3/4 Sidewinder exhaust ceramic header and stainless back box Vband clamp , Deep sump, Jeff Denham welded heads 44 x 37 valves heavily reworked with matching manifolds, Berg linkage, Fuel injection kit-CB throttle bodies, DTA .

Gearbox by Cogbox close 1,2 and 3 gears tall 4th for cruising all welded gears heavy duty side plate, superdiff Sway away short race axles.

http://i71.photobucket.com/albums/i149/gluemixer/th_MOV00001.jpg (http://s71.photobucket.com/albums/i149/gluemixer/?action=view&current=MOV00001.flv)

then to stop i made these fit

http://i71.photobucket.com/albums/i149/gluemixer/DSC00303.jpg

http://i71.photobucket.com/albums/i149/gluemixer/DSC00301.jpg

http://i71.photobucket.com/albums/i149/gluemixer/DSC00680.jpg

so all is going well then i find loads of the ginger stuff bottom of door, some in the wings and heater channels. I found some NOS 65 doors and got hold of some day mouldings wings and painted them then started on the channels

http://i71.photobucket.com/albums/i149/gluemixer/DSC00079.jpg

http://i71.photobucket.com/albums/i149/gluemixer/DSC00081.jpg

http://i71.photobucket.com/albums/i149/gluemixer/DSC00083.jpg

http://i71.photobucket.com/albums/i149/gluemixer/111980355_7gpWRY4E_SBF_1903.jpg

http://i71.photobucket.com/albums/i149/gluemixer/27.jpg

http://i71.photobucket.com/albums/i149/gluemixer/DSCN2429.jpg

http://i71.photobucket.com/albums/i149/gluemixer/DSC01007.jpg

http://i71.photobucket.com/albums/i149/gluemixer/DSC01003.jpg

http://i71.photobucket.com/albums/i149/gluemixer/DSC01005.jpg

now looks like this

http://i71.photobucket.com/albums/i149/gluemixer/th_IMG_0219.jpg~original (http://s71.photobucket.com/albums/i149/gluemixer/?action=view&current=IMG_0219.mp4)

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0582.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0584.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0616.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0599.jpg~original

im fitting a G50 over the winter so watch this space

cheers andy

volkdent

September 12th 2010, 20:31

Very cool, and a nice story too!

You must be a plumber considering all the hoses and fittings you have to deal with!!!

Awesome.

Jason

vdubfund

September 13th 2010, 09:19

Fast65
Looks great!
Just a few question. How is the turning with the calipers sitting on the front side of the wheel? Any hitting the torsion arms?
Did you weld a 944 spindle to a CB spindle? Are those 86 T brakes? Narrowed beam?
I'm in the process of doing something very similar to my 64.
Nice work!

effvee

September 13th 2010, 11:46

Hi, is that a oil tank behind your rear seat? If so, is it vented to the inside also?

Fast65

September 13th 2010, 13:13

Hi, is that a oil tank behind your rear seat? If so, is it vented to the inside also?

hi yes it is an oil tank it does vent out side, the breather was put there so i didnt loose it lol

cheers andy

Fast65

September 13th 2010, 13:17

Fast65
Looks great!
Just a few question.

How is the turning with the calipers sitting on the front side of the wheel?

No problems at all

Any hitting the torsion arms?

none all fine

Did you weld a 944 spindle to a CB spindle?

yes and it is also bolted i have had the welds have been crack tested :)

Are those 86 T brakes?

yes they are

Narrowed beam?

yes 4"

I'm in the process of doing something very similar to my 64

there is also a bit of work to get the rears to fit they dont dont straight on :mad:
.
Nice work!

Cheers thanks

hope that help cheers andy

Steve C

September 13th 2010, 22:31

Hi

What a transformation, well done.

Are you using the A1 headers with your turbo?

Steve

Fast65

September 14th 2010, 03:40

Hi

What a transformation, well done.

Are you using the A1 headers with your turbo?

Steve

thanks, yes im using an a1 header

cheers andy

Steve C

September 14th 2010, 08:53

Hi

That would make it much nicer off boost, do you have any photos of the turbo pipe work after the A1s?

Steve

Fast65

September 14th 2010, 13:00

hi yes

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0042.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0040.jpg~original

and the inlet

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0039.jpg~original

got to change alot of it now as the turbo oil seals failed :(

cheers andy

Fast65

September 14th 2010, 13:22

old holset off and thers still oil coming out another pint

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0746.jpg

the two together

holset is the top one, T4 is the bottom one the T4 has a smaller exhaust and larger compressor wooo :)

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0747.jpg

turbo trial mounted it all looked good until I tried the wheel know its all got to move now but not sure were yet maybe under the boot floor

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0749.jpg~original

but thats for tmw

cheers andy

Humble

September 14th 2010, 16:35

Fast65

September 14th 2010, 17:04

Awesome project, I'd love to see some hp numbers :)

You run out of room quick when you add a turbo, but I do like the way the A1 setup looks. I don't think there's enough room on my car to mount the turbo there.

cheers thanks i cant wait to get some numbers i would love to get 400hp, and yes you soon run out of room

oil cooler here

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0574.jpg~original

look what i did to fit a water injection tank :lmao:

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0336.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0338.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0340.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0342.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0345.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0352.jpg~original

and ive hidden the pump under the feul tank :)

cheers andy

Fast65

September 20th 2010, 15:03

its in :)just got make the muffler fit and sort the idle think ive got an air leak :rolleyes:

http://i71.photobucket.com/albums/i149/gluemixer/th_IMG_0762.jpg (http://s71.photobucket.com/albums/i149/gluemixer/?action=view&current=IMG_0762.mp4)

cheers andy

ricola

September 20th 2010, 17:29

Love how you integrated the water tank, but wouldn't you have gained a lot more volume by putting the filler at the top?

Humble

September 20th 2010, 18:44

I also dig the integrated water tank but you'll have to keep a careful eye on it. I'm going through a gallon of water for every 30-ish gallons of gas I put in my car. It's also easy to forget if you don't see it, I have enough trouble remembering mine behind the passenger seat. :)

Fast65

September 22nd 2010, 15:06

Love how you integrated the water tank, but wouldn't you have gained a lot more volume by putting the filler at the top?

cheers, yes you are correct but its has enough for a 1/4 mile lol

cheers andy

Fast65

September 22nd 2010, 15:07

Fast65

September 22nd 2010, 15:14

more porsche bits today :)

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0764.jpg

Fast65

September 27th 2010, 16:24

the final look

http://i71.photobucket.com/albums/i149/gluemixer/IMG_0769.jpg~original

cheers andy

Fast65

November 19th 2010, 13:29

the first and only run this year roll on next year :)

http://i71.photobucket.com/albums/i149/gluemixer/MF4M01321.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/MF4M01341.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/MF4M01391.jpg~original

cheers andy

Fast65

November 19th 2010, 13:40

ive decided to go for the porka box a G50 box into another chassis and swap over when its done :)

the proka box next to a standard T1 box

http://i71.photobucket.com/albums/i149/gluemixer/1f064cb9.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/e787c6a9.jpg~original

now ive got to make this lot fit

http://i71.photobucket.com/albums/i149/gluemixer/91f10070.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/efa471d9.jpg~original

http://i71.photobucket.com/albums/i149/gluemixer/aa78c82a.jpg~original

well after 20mins with the plasma cutter does this

http://i71.photobucket.com/albums/i149/gluemixer/d63385e0.jpg~original

another 90 mins with the help of a 9" grinder gets this

http://i71.photobucket.com/albums/i149/gluemixer/5714c3e2.jpg~original

thats it so far got to get some metal stock and start rebuilding the chassis with the box in

cheers andy

joeyd63

November 20th 2010, 01:06

very impressive with the g50 in there. is that 5 or 6 speed?

Fast65

November 20th 2010, 11:28

hi thanks, its a 5 speed

cheers andy