Forum: Project Builds
May 18th 2012, 08:57
|
Replies: 620
Views: 382,670
Hi Dave, good looking motor!
I have the...
Hi Dave, good looking motor!
I have the same shifter problem as you, nudging reverse instead of second. I initially thought it was the reverse stop plate but I have noticed that it occurs most...
|
Forum: Brakes
May 18th 2012, 08:29
|
Replies: 6
Views: 5,725
Alex, Red stuff are for high power heavyweight...
Alex, Red stuff are for high power heavyweight cars. Use EBC greenstuff for the same effect. I'm using Greenstuff in 944 single pots and pagid in the 928S4 rears. With Porsche calipers I very much...
|
Forum: Project Builds
March 15th 2012, 14:13
|
Replies: 620
Views: 382,670
Dave, rather than higher wattage bulbs i.e....
Dave, rather than higher wattage bulbs i.e. 100/90 or 130/90 I have used the 60/55W +50% that will get you close to the first upgrade figure and with +80% now being readily available thats what I...
|
Forum: Project Builds
March 13th 2012, 11:51
|
Replies: 620
Views: 382,670
Hi Dave, what's the light patterns - my guess -...
Hi Dave, what's the light patterns - my guess - the two outers are fog wide beam for seeing round corners and the centre two are drive pattern? Did you link the dip onto the main beam? I'm finding...
|
Forum: Project Builds
March 12th 2012, 11:27
|
Replies: 620
Views: 382,670
Dave, sorry for the historic reply but you move...
Dave, sorry for the historic reply but you move too fast for me! I have a hydraulic handbrake in the '03 and had to use a 2psi RPV on the rear line to get anything like a decent pedal as the m/c for...
|
Forum: Suspension
March 5th 2012, 11:41
|
Replies: 14
Views: 8,564
|
Forum: Suspension
March 5th 2012, 11:38
|
Replies: 8
Views: 6,840
|
Forum: Brakes
March 5th 2012, 11:28
|
Replies: 17
Views: 8,967
I have 944 single pots at the front and 928S4 4...
I have 944 single pots at the front and 928S4 4 pots at the rear with a hydraulic handbrake in series with the rear line. I found that the rear line was allowing too much flex within the handbrake...
|
Forum: Project Builds
February 23rd 2012, 09:53
|
Replies: 620
Views: 382,670
|
Forum: Project Builds
February 9th 2012, 13:12
|
Replies: 620
Views: 382,670
|
Forum: Project Builds
February 3rd 2012, 09:50
|
Replies: 620
Views: 382,670
Hi Dave,
I see your kafer bar but does it have...
Hi Dave,
I see your kafer bar but does it have the strut that connects to the frame horn at the inner trailing arm mount? Are you running heat exchangers?
I have been pondering this installation...
|
Forum: Suspension
January 30th 2012, 12:47
|
Replies: 11
Views: 7,143
Riseabove, I run a Spax PSX kit that is...
Riseabove, I run a Spax PSX kit that is progressive with I think 110lb primary rate. This is with a stiffened front end and I feel that when pushed over the country roads around here they work very...
|
Forum: Suspension
January 17th 2012, 09:45
|
Replies: 11
Views: 7,143
|
Forum: Suspension
January 17th 2012, 09:41
|
Replies: 13
Views: 8,298
|
Forum: Suspension
January 17th 2012, 09:35
|
Replies: 58
Views: 32,184
Agreed, I remember when Road Rallying was...
Agreed, I remember when Road Rallying was Pre-Plot (aka road racing) there were a couple of guys who did remarkably well and occasionally winning events with bog standard cars from the local car...
|
Forum: Project Builds
December 20th 2011, 08:35
|
Replies: 620
Views: 382,670
|
Forum: Project Builds
December 19th 2011, 12:05
|
Replies: 620
Views: 382,670
Dave, when you decide to move over to the two...
Dave, when you decide to move over to the two bolt set up, talk to me as I should have by then reverted back to the standard roll centre having used the 3-bolt inner pivot point to lower the roll...
|
Forum: Project Builds
December 13th 2011, 07:27
|
Replies: 620
Views: 382,670
Dave,
Have a look at the 2nd photo down: ...
Dave,
Have a look at the 2nd photo down: http://www.jemsracing.co.uk/cs_widetrack.html The photo is of an Escort racer taken from the underside but shows the normal TCA at 90* to the frame but...
|
Forum: Project Builds
December 12th 2011, 08:32
|
Replies: 620
Views: 382,670
Hi Dave, have you thought about installing a...
Hi Dave, have you thought about installing a compression strut for the front suspension and then disconnecting the anti-roll bar from the caster control duty? That would have serious benefits, the...
|
Forum: Project Builds
December 9th 2011, 10:14
|
Replies: 620
Views: 382,670
|
Forum: Suspension
December 8th 2011, 08:44
|
Replies: 48
Views: 57,783
|
Forum: Suspension
December 7th 2011, 09:00
|
Replies: 48
Views: 57,783
|
Forum: Project Builds
December 6th 2011, 11:30
|
Replies: 1,572
Views: 804,997
Dave, don't you use the snowbanks in good...
Dave, don't you use the snowbanks in good Scandinavian style? On the rare occasions we have decent snow with better than 1/2m high banks I just love kissing the banks to aid turn in!:D:D
( we are...
|
Forum: Suspension
December 6th 2011, 10:51
|
Replies: 48
Views: 57,783
Sorry for the delay folks - been busy.
...
Sorry for the delay folks - been busy.
Adding my sixpennyworth. I have Spax PSX progressives on the front of the '03 that I estimate are 100 - 130lb/in over the travel distance. On the back I...
|
Forum: Project Builds
November 18th 2011, 08:21
|
Replies: 154
Views: 153,381
|