Forum: Suspension
February 9th 2004, 17:24
|
|
Replies: 12
Views: 4,933
i wasn't referring to the arms but the rotors...
i wasn't referring to the arms but the rotors themselves. i was (am) under the impression that its the rotors and not the trailing arms themselves that increase track width. not positive how much...
|
|
Forum: Suspension
February 9th 2004, 14:38
|
|
Replies: 12
Views: 4,933
|
|
Forum: Suspension
January 20th 2004, 16:37
|
|
Replies: 2
Views: 2,163
|
|
Forum: Suspension
January 11th 2004, 21:30
|
|
Replies: 25
Views: 4,263
|
|
Forum: Suspension
January 11th 2004, 00:39
|
|
Replies: 25
Views: 4,263
so if i'm picturing this right your going to...
so if i'm picturing this right your going to slide a pipe or similar into the trailing arm pivot hole/bushing then mount your spring plate/hiem joint on the arm and adjust the heim so it sits in the...
|
|
Forum: Suspension
January 10th 2004, 01:20
|
|
Replies: 25
Views: 4,263
Dorigtt, yes on my irs bug i have narrowed just...
Dorigtt, yes on my irs bug i have narrowed just the torsion tubes and according to my calculations the only difference i have to make is when i mount my heim, instead of mounting it in the middle of...
|
|
Forum: Suspension
January 9th 2004, 19:26
|
|
Replies: 25
Views: 4,263
yeah the two pivots have to intersect. i...
yeah the two pivots have to intersect. i measured the trailing arm pivot and it has a pitch of 9/32" rise per inch. so if you narrow 2 inches (2" * 9/32" = 9/16") so if find the center of the...
|
|
Forum: Suspension
January 9th 2004, 01:00
|
|
Replies: 25
Views: 4,263
|
|
Forum: Suspension
January 8th 2004, 19:35
|
|
Replies: 25
Views: 4,263
hey panalfantastic i already posted it under...
hey panalfantastic i already posted it under narrowed irs but wan't sure if you knew. i did the measuring and for an irs car narrowed 2" per side you can move the pivot (hiem) back 9/16 and it...
|
|
Forum: Suspension
January 8th 2004, 19:30
|
|
Replies: 12
Views: 4,933
|
|
Forum: Suspension
January 3rd 2004, 22:34
|
|
Replies: 2
Views: 2,163
narrowed irs
well i'm in the process of narrowing my rear irs and have the torsion tube narrowed 2" per side and have learned alot. the process is really not hard. i used hose clamps to guide my cuts and used a...
|
|
Forum: Suspension
December 25th 2003, 15:48
|
|
Replies: 25
Views: 4,263
I'm assuming these are similar to the ones...
I'm assuming these are similar to the ones available at aircooled.net. or not? Is it possible to move the shock mount as well as the spring plate mount? well in my case it would be a coilover mount...
|
|
Forum: Suspension
December 24th 2003, 20:41
|
|
Replies: 12
Views: 4,933
|
|
Forum: Suspension
December 24th 2003, 14:07
|
|
Replies: 12
Views: 4,933
kerscher rear vented discs?
I think i've opted for the kerscher rotor on cb spindle with the 944 4 pot caliper up front. Seems simple enough. For the rear i'd like a similar setup but can't find any kerscher vented rear...
|
