GermanLook Forums  

Go Back   GermanLook Forums > Search Forums

Showing results 1 to 25 of 67
Search took 0.01 seconds.
Search: Posts Made By: Blizzard
Forum: Project Builds July 1st 2020, 04:34
Replies: 73
Views: 13,389
Posted By Blizzard
Already had a few sets of late model caps without...

Already had a few sets of late model caps without the hole, so in my case this was easier.
Forum: Project Builds June 30th 2020, 15:09
Replies: 73
Views: 13,389
Posted By Blizzard
Drilled a square hole for the speedo cable in the...

Drilled a square hole for the speedo cable in the hub dustcap.

https://i.imgur.com/rJAgdMj.jpg?1

Just fitted new wheel bearings so every component can finaly be bolted together.
...
Forum: Project Builds June 30th 2020, 14:57
Replies: 73
Views: 13,389
Posted By Blizzard
The new 18" wheels are for the black 1303. It...

The new 18" wheels are for the black 1303. It will have 2 OMP race bucket seats and a red rollcage. So it stands out no matter what color wheels I put under the thing I personaly still lean towards...
Forum: Project Builds June 30th 2020, 03:51
Replies: 73
Views: 13,389
Posted By Blizzard
The black set of Porsche BBS Sport Classic 2...

The black set of Porsche BBS Sport Classic 2 wheels were already sold but the seller had an other very nice set in Silver. The rear is 9J and the front is 7,5J.
Most sets of SC 2's are with a 10J...
Forum: Project Builds June 30th 2020, 03:27
Replies: 73
Views: 13,389
Posted By Blizzard
No turbo yet, but I do have my '86 944 turbo...

No turbo yet, but I do have my '86 944 turbo front brakes complete.

I already had the spindles and calipers but was still looking for the hard to find and expencive '86 turbo hubs.
...
Forum: Body June 17th 2020, 15:17
Replies: 12
Views: 284
Posted By Blizzard
It has been done before to weld the reinforced...

It has been done before to weld the reinforced heater channel rails from a convertible under a sedan.

https://i.imgur.com/lZOV1UJ.jpg

But you already want to delete the heaterboxes, why don't...
Forum: Project Builds May 27th 2020, 17:57
Replies: 73
Views: 13,389
Posted By Blizzard
Not mine yet but these are what I have in mind...

Not mine yet but these are what I have in mind for the black super.

https://i.imgur.com/e5ZwYNe.jpg
Forum: Project Builds May 27th 2020, 17:38
Replies: 73
Views: 13,389
Posted By Blizzard
Just for fun and to see the difference. The 9J...

Just for fun and to see the difference.
The 9J ET70 Cup2 with 255 tyre and 4 cm. spacers under stock fenders.

https://i.imgur.com/ctSrGor.jpg?1

And the same wheel tyre combo and spacer under...
Forum: Project Builds May 27th 2020, 17:07
Replies: 73
Views: 13,389
Posted By Blizzard
The 6 cm wider fiberglass fenders are bent out of...

The 6 cm wider fiberglass fenders are bent out of shape from hanging on a wall for 8 years, thats why the fender does'nt follow the same radius as the tyre. On the pictures at Spa they are'nt even...
Forum: Project Builds May 27th 2020, 16:51
Replies: 73
Views: 13,389
Posted By Blizzard
245 / 40 / 17" The setup on the photo's in the...

245 / 40 / 17" The setup on the photo's in the rear is the 8,5"sport classic's with 245 tyres with 4 cm. spacers under 6 cm. wider rear fenders. Front is the same as mentioned before only the wheel...
Forum: Project Builds May 26th 2020, 04:21
Replies: 61
Views: 8,539
Posted By Blizzard
I'm sorry but I think you're making a mistake...

I'm sorry but I think you're making a mistake with the holes in the pushrods. All they do is leak oil into the heads. Oil takes the path of least resistance, cousing no oil pressure in the rockers....
Forum: Project Builds May 25th 2020, 16:24
Replies: 61
Views: 8,539
Posted By Blizzard
Have you done any other mods to ensure oil...

Have you done any other mods to ensure oil reaches the valve stems through the rockers? For example,
connect the 2 oil grooves in the cam followers,
cut oli grooves in the rocker shaft so oil can...
Forum: Project Builds May 24th 2020, 16:28
Replies: 73
Views: 13,389
Posted By Blizzard
This topic started with my black '75 1303. The...

This topic started with my black '75 1303. The titel of the topic is rolling rebuid, But it's not rolling at the moment. All the previous welding I did was to keep it on the street asap and street...
Forum: Project Builds May 23rd 2020, 06:40
Replies: 73
Views: 13,389
Posted By Blizzard
DIY oilcooler bracket and airscoop. The...

DIY oilcooler bracket and airscoop.

The olilines in the final instalation go over the driveshaft and the CSP shocktower brace / torque bar. With the type 4 the thermostat and oilfilter are on the...
Forum: Project Builds May 23rd 2020, 06:14
Replies: 73
Views: 13,389
Posted By Blizzard
Some DIY made stuff How to connect your...

Some DIY made stuff

How to connect your throttle cable to your new CSP type 4 carb linkage? There is no bracket to hold the cable included. So I made my own. Some angle alluminium and a bicycle...
Forum: Project Builds May 23rd 2020, 05:05
Replies: 73
Views: 13,389
Posted By Blizzard
I'm done with photobucket. The photo's that are...

I'm done with photobucket. The photo's that are not vissable are no longer in my photobucket albums. Last few photo's are hosted on IMGUR. I will try to (re)post the most important technical photo's...
Forum: Project Builds May 21st 2020, 05:24
Replies: 73
Views: 13,389
Posted By Blizzard
@ effvee The brake parts used in this car are...

@ effvee
The brake parts used in this car are on page 2 of this topic.
The only things I had made or made myself are the bearing adapters for the 944 S2 front hub on 944 NA spindels, the second...
Forum: Project Builds May 20th 2020, 13:49
Replies: 73
Views: 13,389
Posted By Blizzard
Update on my red '75 1303 From this at Spa...

Update on my red '75 1303

From this at Spa 2018

https://i.imgur.com/y8vDMCH.jpg?1

To this at Spa 2019

https://i.imgur.com/dCfLwRM.jpg?1
Forum: Suspension August 14th 2018, 17:27
Replies: 7
Views: 2,453
Posted By Blizzard
To give an other posible answer to your problem....

To give an other posible answer to your problem. Are the torsionbars all the way in the splines of the springplate and the torsionbar housing on the chassis. ? Try cleaning the splines in the...
Forum: Suspension August 14th 2018, 17:19
Replies: 7
Views: 2,453
Posted By Blizzard
No the koni"s are for an IRS beetle. I have made...

No the koni"s are for an IRS beetle. I have made the lower urathane bushing out of a set of 19 mm front swaybar bushings and a friend with a lathe made the steel inserts. outside 19mm. inside 14mm.
...
Forum: Suspension August 6th 2018, 15:14
Replies: 7
Views: 2,453
Posted By Blizzard
http://i129.photobucket.com/albums/p207/blizzard19...

http://i129.photobucket.com/albums/p207/blizzard1974/1303%20LS%201975/Afbeelding005-1.jpg (http://s129.photobucket.com/user/blizzard1974/media/1303%20LS%201975/Afbeelding005-1.jpg.html)
...
Forum: Suspension August 6th 2018, 14:52
Replies: 7
Views: 2,453
Posted By Blizzard
Is the original rubber still on the inner side of...

Is the original rubber still on the inner side of the 944 spring plate? If so remove this rubber and replace it with one for a beetle.
Forum: Project Builds April 24th 2017, 15:51
Replies: 73
Views: 13,389
Posted By Blizzard
Some photos of the damage and repairs. ...

Some photos of the damage and repairs.

http://i129.photobucket.com/albums/p207/blizzard1974/100_4967_zpsr00huit2.jpg~original...
Forum: Project Builds April 24th 2017, 15:28
Replies: 73
Views: 13,389
Posted By Blizzard
This is a quote from 29 september 2014. ...

This is a quote from 29 september 2014.

Finaly I took the red 1303 to a wheel alignment garage. I promiced to post the degrees of toe-in, camber and so on. The reason it took so long is because I...
Forum: Project Builds August 22nd 2015, 16:42
Replies: 73
Views: 13,389
Posted By Blizzard
Front. KW inox coilover set. Home made camber...

Front.
KW inox coilover set. Home made camber plate. 944 NA spindle (with hole for speedo cable) with custom bearing spacers. 944 S2 hubs without ABS. 944 turbo '87> brake rotors. 2006 Boxter S...
Showing results 1 to 25 of 67

 
Forum Jump

All times are GMT -4. The time now is 14:16.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
© www.GermanLook.net 2002-2017. All Rights Reserved