Forum: Engines
September 23rd 2016, 11:16
|
Replies: 7
Views: 8,984
|
Forum: Wheels
September 22nd 2016, 15:33
|
Replies: 15
Views: 32,453
|
Forum: Engines
September 22nd 2016, 11:42
|
Replies: 7
Views: 8,984
|
Forum: Project Builds
May 28th 2016, 09:18
|
Replies: 398
Views: 283,659
One thing I don't like is the Subaru hypoid r&p...
One thing I don't like is the Subaru hypoid r&p for correct drive shaft alignment tho, I looked at them when I built my 4x4 Rallycross '03 and had an option with used prodrive development 'boxes, at...
|
Forum: Project Builds
May 27th 2016, 13:16
|
Replies: 398
Views: 283,659
|
Forum: Project Builds
February 15th 2016, 04:21
|
Replies: 155
Views: 61,597
There is a given with grinding gear selection,...
There is a given with grinding gear selection, the driven plate is exactly that, it's being driven, it's rotating with the fly when it should be ' released' and not free, so you can't get gears, two...
|
Forum: Project Builds
February 14th 2016, 16:22
|
Replies: 132
Views: 92,830
|
Forum: Project Builds
February 11th 2016, 15:41
|
Replies: 132
Views: 92,830
|
Forum: Body
January 22nd 2016, 16:37
|
Replies: 11
Views: 2,807
Any good.
...
Any good.
http://www.eagleownersclub.org.uk/Technical/vw_dimensions.jpg
|
Forum: Body
December 27th 2015, 13:41
|
Replies: 6
Views: 1,523
|
Forum: Project Builds
November 4th 2015, 17:24
|
Replies: 36
Views: 27,156
Alex, We are of topic, so briefly, with dry sump,...
Alex, We are of topic, so briefly, with dry sump, a sump extension is alien, just added weight and complexity, it misses the point of d/s completely.
I run a raised trans for racing anyway, I do it...
|
Forum: Engines
September 22nd 2015, 10:03
|
Replies: 3
Views: 9,502
You are right to bin the bolt on sump, it's nor...
You are right to bin the bolt on sump, it's nor required with dry sump, is the pump shown the one you are using? Single stage is limited in volume obviously, why not use a two stage?, Autocraft or...
|
Forum: Suspension
June 4th 2015, 11:17
|
Replies: 16
Views: 19,835
|
Forum: Suspension
May 31st 2015, 09:26
|
Replies: 16
Views: 19,835
My concern is More the cyclic loads suspension...
My concern is More the cyclic loads suspension components have to contend with, rather than a calculated yield point, it wouldn't be too difficult to calculate the yield point of the bolts, even from...
|
Forum: Suspension
May 26th 2015, 15:15
|
Replies: 16
Views: 19,835
|
Forum: Suspension
May 21st 2015, 17:41
|
Replies: 16
Views: 19,835
|
Forum: Suspension
May 21st 2015, 11:06
|
Replies: 16
Views: 19,835
Interesting the two separate setups above, one...
Interesting the two separate setups above, one using a 6 rib bus box with torsion tube intact, the other with much longer Subaru 'box with a sectioned and overhead 'bridge' plate reinforced torsion...
|
Forum: Suspension
May 21st 2015, 08:47
|
Replies: 16
Views: 19,835
|
Forum: Suspension
May 20th 2015, 16:53
|
Replies: 16
Views: 19,835
It depends on the agenda you have for the car,...
It depends on the agenda you have for the car, generally, for all but very smooth surfaces, there is insufficient travel before the shock bottoms out, ideally the travel needs to be increased by...
|
Forum: Project Builds
April 10th 2015, 12:31
|
Replies: 110
Views: 116,379
|
Forum: Project Builds
January 22nd 2015, 05:23
|
Replies: 64
Views: 86,329
|
Forum: Project Builds
January 19th 2015, 10:25
|
Replies: 403
Views: 216,173
I'm sure it will be fine, The loads are well...
I'm sure it will be fine, The loads are well distributed in your design, brilliant height adjuster idea, but the lower bolts would keep me awake, I know they are super tough, but could you not run a...
|
Forum: Project Builds
January 17th 2015, 16:59
|
Replies: 403
Views: 216,173
|
Forum: Engines
November 18th 2014, 12:33
|
Replies: 2
Views: 3,444
|
Forum: Project Builds
October 27th 2014, 12:56
|
Replies: 105
Views: 78,424
Alex, Wally, Here you can see the mounting pad...
Alex, Wally, Here you can see the mounting pad concerned, just above were the torsion bar end plate fits, also from the mists of time, I seem to remember four bolts used on very early models, ie, two...
|