GermanLook Forums  

Go Back   GermanLook Forums > Search Forums

Showing results 1 to 20 of 20
Search took 0.00 seconds.
Search: Posts Made By: Bugnutz
Forum: Brakes April 16th 2008, 20:59
Replies: 21
Views: 9,658
Posted By Bugnutz
the 944 master cylinder (thru 86, p/n...

the 944 master cylinder (thru 86, p/n 944.355.011.01) is 23mm front and 19mm rear.
Forum: Suspension June 20th 2007, 23:51
Replies: 26
Views: 7,146
Posted By Bugnutz
Weltmeister is the word

Steve-

I checked the Pelican website and you are right, the site no longer lists the item for the 944, only the 924. You may wish to call them and inquire. The bushings I got from them have "...
Forum: Suspension March 4th 2007, 19:28
Replies: 26
Views: 7,146
Posted By Bugnutz
snow

Snow's not so bad here, but fifty miles East is another story- Oswego NY was on the national news for ten feet of snow a couple of weeks back, maybe you saw it.
Forum: Suspension March 4th 2007, 19:04
Replies: 26
Views: 7,146
Posted By Bugnutz
Those bolts

JR,

Those pivot bolts and the washers that go with them are hard to find but Aircooled.net has new ones.

-Mark.
Forum: Suspension March 4th 2007, 08:30
Replies: 26
Views: 7,146
Posted By Bugnutz
Pivot bolt

JR,

Those bolts are 14x1.5 and 80 mm long.

I just used the stock beetle IRS pivot bolts after swapping the aluminum trailing arm's rubber bushings for some urethane units made for the beetle. ...
Forum: Suspension April 5th 2005, 15:01
Replies: 4
Views: 2,712
Posted By Bugnutz
What's wrong with this picture?

NIce pic, but I have to ask: Is it just me or is that caliper upside-down (bleeder valve is the cue)?

Bugnutz.
Forum: Suspension September 7th 2004, 10:00
Replies: 6
Views: 2,296
Posted By Bugnutz
went in another direction

Hey, sorry to be so long with a reply. I decided to save the ghia stuff for another project, and went with a pair of billet hubs and caliper adapters to fit on BJ drum brake spindles from VDUB...
Forum: Suspension April 7th 2004, 10:30
Replies: 5
Views: 2,414
Posted By Bugnutz
Found some at racer's edge

Guys,

I found that Racer's Edge has Delrin inner and outer bushings for the 944. I had been considering filling part of the 944 cast aluminum spring plate retainers with thickened epoxy and using...
Forum: Suspension April 2nd 2004, 07:52
Replies: 5
Views: 2,414
Posted By Bugnutz
need source for bushings

Hello All,

Does anyone have a source for urethane bushings to fit the 944 spring plate? I am talking about the outer side bushing, the one that fits underneath the cast aluminum torsion cover.
...
Forum: Group buys February 26th 2004, 09:50
Replies: 13
Views: 1,686
Posted By Bugnutz
Just let me know where to send the cash...

Brendan,

Looks like I'll be needing a set of bearing spacers for my car after all. Send me an e-mail with the details mpetrush@frontiernet.net

Regards, Mark.
Forum: Suspension February 23rd 2004, 14:18
Replies: 67
Views: 70,326
Posted By Bugnutz
On the same case!

Zen,

Thanks a lot for sending the photos. I am working on exactly the same problem- I don't have enough fender clearance, and will need to change from the late "dished" hubs and wider hat...
Forum: Off Topic February 19th 2004, 11:35
Replies: 5
Views: 2,935
Posted By Bugnutz
When did your obsession begin?

Literally while still in diapers. My dad was buying beetles in the 1950's before there was much of a dealer network and you had to go to NYC to get them. We always got a Deluxe Sunroof Sedan, and he...
Forum: Suspension October 25th 2003, 19:25
Replies: 16
Views: 4,243
Posted By Bugnutz
Fuchs alloy weights

The scale used is a big factor, and yes the common bathroom scales can lie.

FWIW, I just happen to have my wheels here with no tires mounted yet. I weighed them with a Chatillon spring scale...
Forum: Transmissions October 7th 2003, 08:23
Replies: 2
Views: 2,450
Posted By Bugnutz
5Ks trans

Wolfy-

This sounds kinda interesting, but the page you referenced was talking about using the 5000S transmission in a mid-engine chassis, where the rotation of the engine and trans would be the...
Forum: Suspension August 2nd 2003, 14:15
Replies: 6
Views: 2,288
Posted By Bugnutz
bolt spacing

As near as I can measure it the caliper bolt spacing on a Type I Karmann Ghia spindle is 56 mm.

-Regards, Mark.
Forum: Suspension July 25th 2003, 18:04
Replies: 21
Views: 5,593
Posted By Bugnutz
Same here

Humble-

It would seem that all 1986 944 aluminum trailing arms are not created equal. I have a pair from an '86 and they are also the wide track.

Regards, Mark.
Forum: Suspension July 11th 2003, 08:57
Replies: 6
Views: 2,296
Posted By Bugnutz
Nice...

Steve-

That's some really nice work!!! Thank you for posting the pic.

-Mark.
Forum: Suspension July 10th 2003, 09:42
Replies: 6
Views: 2,296
Posted By Bugnutz
Lightbulb Diameter of 944 turbo front hub

Hello all-

Can anyone supply me with the outside diameter of the Porsche 944 turbo front hub? These are the ones where the brake rotor 'hat section' fits on from the outside in normal fashion, as...
Forum: German Look Tuning July 3rd 2003, 15:01
Replies: 29
Views: 5,631
Posted By Bugnutz
takin' a shave

Vujade, I spent my .02 worth and weighed in for shaving the trim off.

On my car I removed the body and window rubber trim strips, blacked out the vent wings and door glass scraper frames, painted...
Forum: Suspension June 28th 2003, 12:04
Replies: 67
Views: 70,326
Posted By Bugnutz
944 alloy trailing arm part #'s

All,

This is my first post to the forum.

I bought some 944 trailing arms from a Porsche dismantler.
I requested the 'early' narrow track version, but when they arrived I found the wide track...
Showing results 1 to 20 of 20

 
Forum Jump

All times are GMT -4. The time now is 05:32.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© www.GermanLook.net 2002-2017. All Rights Reserved