Quote:
Originally Posted by VWCoupet
Thanks for the responses. I live in Metro Vancouver (BC). My daily drive is about 30 minutes. It is a little freeway, a little highway, plus some farm roads and a wee bit through "town".
I do love to drive up to Whistler which is about a 2.75 hour drive and to Kelowna (3.5 hrs) .Both of these trips are a real challenge to a stock air cooled 1600DP. I also love to head down to Seattle WA and Portland and have taken the car down as far as Long Beach CA where I have some family.
If I got the car "just right" (excluding a 5 speed and a Type IV) I would then consider a larger motor and look into racing it at a road circuit course.
When I initially started the project I went through a couple of Keith Seume's books. This is what I came up with. (Please do comment.)
- upgrade stock rubber bushes to heavy duty urethane
- recondition ball-joints and replace rubber boots
- replace wheel bearings
- install Bilstein or Koni shocks
- swap the semi-trailing arm over from one side to the other whilst at the same time trimming off and swapping the shock absorber mountings so that they are now below the trailing arms once more (???)
- reset so that the wheels have a slight negative camber.
- on the front end - overhaul, i.e. replace each component that show signs of wear. (E.G. rubber bushes, strut inserts, strut bearings, and ball joints.)
- install an uprated sway bar
- install a new steering damper (Koni)
- install a pair of adjustable short struts and Koni (or Bilstein gas shocks)
The pan itself requires a hole repair. I will wire wheel it and clean and seal it up.
While I have such great access I plan to clean and replace everything that should reasonably be replaced and uprated. What should I consider here?
Like I say, I am somewhat ignorant of these things. I used Muir's book, the Bentley manual, and Rick's "Bug Me Video"(s) to get the body separated from the pan and to do the engine removal and tear down. This all went quite well and I was pleased that I could remove the body all on my own with just a good jack.
Despite (or maybe because of) my ignorance, I am happy to tackle the project. I just don't know all the details on what I need to consider. I need an overall idea of the complete suspension (including brakes, wheels and tires) before I set out buying and installing parts.
I do appreciate all your responses.
Cheers,
P.S. I will try to upload some photos this weekend. Here too I am somewhat ignorant. Gee, I hope that I'm not just "eye candy" and that there really is something more substantial going on with me.
|
It sounds as though you have reasonable smooth roads to play on but you will require a 'performance street' set up rather than a solid circuit one.
The quick and easiest way to uprate everything would be to source a whole 924S or 944 rear suspension and brakes with a pair of similar front legs together with '03 track control arm (or fabricate them yourself - I did). Don't get the auto box version as the driveshafts are different lengths side to side. You will require VW181 output flanges to the gearbox but all in all its a reasonable bolt-on procedure with much less fabbing than Keith Seume's suggestions. Plus you will get top spec for possibly less money. I managed to get a whole 924S undercarriage for £65 + 928 rear calipers (£140) + a Spax PSX suspension (£328). In fabbing the track control arm you could consider a compression strut that would allow you to add caster adjustability and anti-dive as well as taking the weak link IMO of having the anti-roll bar controlling the fore and aft movement. The fabricated track control arm then allows you to use the bolt-on 944 bottom ball joint that makes maintenance much less of a headache.
The 924S/944 route gives you:
Alloy fully adjusable suspension arms (camber and toe in)
23.5 mm uprated torsion bars
Possibly a 14mm anti-roll bar
Big CVs and driveshafts
290mm rear discs
280mm front discs
Big single pot front calipers
Big fully adjustable struts
As regards KS's suggestions:
The bushes need the hardest ones (85%+ shore) for the suspension bushes and 80% elsewhere (beware Californian ones as they are not suited to the cooler climes - need to be self lubricating)
Agreed
Agreed
Agreed
Swapping the trailing arm over is there to induce neg camber - a bit of fabbing + you are stuck without any adjustability. When they are swapped over the damper cup mount is on the top and upside down. Therefore it has to be cut off and rewelded the right way up.
Agreed.
I wouldn't uprate the front anti roll bar without considering a rear anti-roll bar to balance it
I note there is no mention of uprated springing. My suggestions are:
Rear 924S/944/type 3 std 23.5mm torsion bars. Increased spinging over this can be had with adding coilovers. Lower 40-50mm.
Front 100-120lb/in lowering springs 40-50mm.
The inner track control arm could usefully be lowered by 25-30mm to load up the front outer wheel more effectively.
If you stayed with the standard anti-roll bar configuration I would consider dropping the rollbar mount by 30-50mm (adjustable with shims) to increase the anti-dive.