#1
|
|||
|
|||
Steering wheel size
Hi Everyone,
Sorry if this has been done before,I tried searching and couldn't find anything. I have a 1974 1303 and want to put a non-stock steering wheel in. However the temporary sports steering wheel that is in there at the moment is too small in diameter and blocks some of my speedo. I know this is a common problem in 1303's. What size steering wheel is big enough to stop this problem? And what different makes of steering wheel offer one in the correct size? It shouldnt make a difference but this is for a RHD car in Australia. Thanks |
#2
|
||||
|
||||
hey BugLuv
well I also have a 74 and I have changed my wheel I have a Sparco wheel and you can use a Momo adapter or you can just use any momo wheel too. hope this helps Chris. |
#3
|
||||
|
||||
The steering hub size had a mid-year change in 1974. The earlier ones are the same as an '85 911. Same goes for 1971-73. The later ones are the same an A2 flatformed Golf (1985-92). Same goes for 1975-79.
__________________
(2004-2008): 1971 1302 w/2056 Searching for a new project ... |
#4
|
||||
|
||||
Hi
I have a 74 1303 as well. I'm using a 350 mm Momo wheel. I'm a little over 6 foot and I cant see the top of the wheel, but when I had my speedo out, I had the lines extended at each 10kph marking towards the centre, it helps. My car uses the later style splines on the hub, fine spline with a taper. I've thought of several different ways to combat this, lower the seats, lower the speedo in the dash, fit a smaller speedo in the same hole that can sit lower down or fit a 2 inch speedo where the clock would sit. Like these ones http://egauges.com/vdo_mult3.asp?Typ...ries=Cyber_Red from Cyberdyne Steve
__________________
STI powered 1303 in the works. |
#5
|
||||
|
||||
Bugluv,
Thanks for posting this request. I am in the process of replacing my steering wheel on my '73 standard Type 1. I want to go with a Momo and they have adapters for early and later models but am not sure of the depth or dish that would work best. The 350mm size seems about right. The Monte Carlo looks like it might work and a friend has the Mod 07 (?) but the dish may be too deep.
__________________
73 Type 1 - 2270 Type IV 64 Type 34 - 1500 Type III |
#6
|
|||
|
|||
Thanks for the advice
|
#7
|
|||
|
|||
To me those momo and sparco steering wheels remind me to much of the movies The Fast And The Furious, 2 Fast 2 Furious and Tokyo Drift HAHA!
I like the oldschool Grant GT slotted steering wheel, of course those Momos wouldnt look right in my car because they wouldnt match my window cranks which are slotted also. |
#8
|
||||
|
||||
i got a momo copy wheel that has an offset hub so it sits just right to see the speedo
however ive just swapped for a new momo one and back to the same old prob
__________________
1974 Germanlook 1303 SUBA-beetle Subaru EJ254, BoostR 17", topline suspension, 4 wheel discs and A/C |
#9
|
|||
|
|||
That looks great! what brand is the copy and where did you get it & the hub?
Thanks |
#10
|
||||
|
||||
Hi Jeol
Did someone say the "fast and the furious"
__________________
STI powered 1303 in the works. |
#11
|
||||
|
||||
just want to share my steering wheel, it's a Classic Nardi suede steering wheel, 13.5 i think, I think it'll do good on a 1303-S.
Last edited by euro1302s; February 27th 2008 at 14:42. |
#12
|
||||
|
||||
Hi Steve,
dreadfull isnt it all be gone this weekend this is the kind of momo corse steering ive got to put in it: plus ive also got all new autometer gauges to go in and im loosing the candy apple red dash panel, going carbon fibre this time Bugluv its just the TypeR kind of ebay cost me $40 and the boss kit was from one of my other bugs but u can also get them on ebay easy enough as well
__________________
1974 Germanlook 1303 SUBA-beetle Subaru EJ254, BoostR 17", topline suspension, 4 wheel discs and A/C Last edited by Joel; February 28th 2008 at 02:00. |
#13
|
||||
|
||||
Hi Joel
I wasn't bagging your car, I just meant that it was looking fully sik maate. Are you going real carbon fibre? I bought some carbon fibre look contact paper from a sign writing supply place. Steve
__________________
STI powered 1303 in the works. |
#14
|
||||
|
||||
LOL its ok i knew u wernt :righton:
it seemed like a good idea at the time.... im going the same way as u, just some CF styling film real CF here in aus would cost half the national debt im tossing up whether to do my running boards as well the stuff ive got is for motorbike bodywork so is weather proof
__________________
1974 Germanlook 1303 SUBA-beetle Subaru EJ254, BoostR 17", topline suspension, 4 wheel discs and A/C |
#15
|
||||
|
||||
Hi Joel
The stuff that I used was very thin, it was very easy mould around curves but the surface would have to be very smooth. It was meant for outside signs so it would be weather proof. Steve This was the stuff I used on my old 1302
__________________
STI powered 1303 in the works. Last edited by Steve C; February 28th 2008 at 18:58. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|