GermanLook Forums  

Go Back   GermanLook Forums > Technical Section > Body

Reply
 
Thread Tools Display Modes
  #1  
Old January 21st 2016, 12:23
graham's Avatar
graham graham is offline
Registered User
 
Join Date: Feb 2004
Location: surrey England
Posts: 273
1303 floor pan dimension ?

Wasn't sure where to post this question but...

Does anyone have a bare 1303 floor pan, I need a measurement from the rear of the torsion tube to the end of the frame horns.

Any help would be much appreciated.
__________________
gee dub
Reply With Quote
  #2  
Old January 21st 2016, 15:26
Wally's Avatar
Wally Wally is offline
Registered User
 
Join Date: Nov 2002
Location: The Netherlands
Posts: 2,534
Nah, no loose floor pan but my engine is out, so then measurement would be easy then too right?
Rear of torsion tube is against the tube vertically?
__________________
'75 Super.
...because race car!

Last edited by Wally; January 21st 2016 at 15:36.
Reply With Quote
  #3  
Old January 21st 2016, 16:11
ricola's Avatar
ricola ricola is offline
Registered User
 
Join Date: Jul 2002
Location: Warwick, UK
Posts: 1,130
don't forget it necks in for the splined section..
__________________
http://www.ricola.co.uk
Reply With Quote
  #4  
Old January 22nd 2016, 01:26
graham's Avatar
graham graham is offline
Registered User
 
Join Date: Feb 2004
Location: surrey England
Posts: 273
Thanks fellas, I ve sent you both pm's .
__________________
gee dub
Reply With Quote
  #5  
Old January 22nd 2016, 01:33
cookvw's Avatar
cookvw cookvw is offline
Registered User
 
Join Date: Apr 2005
Location: Durango, coloRADo, USA
Posts: 222
i have a bare 1303 pan that i can get measurent for ya.
Reply With Quote
  #6  
Old January 22nd 2016, 04:36
graham's Avatar
graham graham is offline
Registered User
 
Join Date: Feb 2004
Location: surrey England
Posts: 273
Ah thanks CookVW that would be great. As Ricola has said the torsion tube necks in for the splined section so if you could please give the dimension from the main/large section of the torsion tube that would really be helpful.

Graham
__________________
gee dub
Reply With Quote
  #7  
Old January 22nd 2016, 16:37
spannermanager spannermanager is offline
Registered User
 
Join Date: Nov 2005
Location: London and kent.
Posts: 185
Any good.

http://www.eagleownersclub.org.uk/Te...dimensions.jpg
Reply With Quote
  #8  
Old January 22nd 2016, 17:36
graham's Avatar
graham graham is offline
Registered User
 
Join Date: Feb 2004
Location: surrey England
Posts: 273
Quote:
Originally Posted by spannermanager View Post
Cheers Spanners not sure if I can get it off this drawing though as its not to scale. Ideally i need the dimension from the back of the torsion tube to end of the frame horns. The drawing here only shows it to the inside of the pan and the body is on my car. If any one is wondering why I don't just measure mine its because the frame horns have already been removed
__________________
gee dub
Reply With Quote
  #9  
Old January 25th 2016, 23:47
cookvw's Avatar
cookvw cookvw is offline
Registered User
 
Join Date: Apr 2005
Location: Durango, coloRADo, USA
Posts: 222
i will get you the needed dimensions in the morning and ill post them up asap.
Reply With Quote
  #10  
Old January 26th 2016, 01:10
Steve C's Avatar
Steve C Steve C is offline
Registered User
 
Join Date: Sep 2002
Location: Sydney, Australia
Posts: 1,716
Hi Just measures a spare 75 1303 pan at the side of my garage, its 53cm, thats from a straight edge across the ends of the horns to the torsion bar tube just out from the pivot box
__________________
STI powered 1303 in the works.
Reply With Quote
  #11  
Old January 26th 2016, 17:50
graham's Avatar
graham graham is offline
Registered User
 
Join Date: Feb 2004
Location: surrey England
Posts: 273
Quote:
Originally Posted by Steve C View Post
Hi Just measures a spare 75 1303 pan at the side of my garage, its 53cm, thats from a straight edge across the ends of the horns to the torsion bar tube just out from the pivot box
Thanks for taking the time to do that Steve
__________________
gee dub
Reply With Quote
  #12  
Old January 26th 2016, 17:57
graham's Avatar
graham graham is offline
Registered User
 
Join Date: Feb 2004
Location: surrey England
Posts: 273
Quote:
Originally Posted by cookvw View Post
i will get you the needed dimensions in the morning and ill post them up asap.
Thanks for your response cookvw but I've sorted it, as you can see Steve C has had his measuring stick out

Thats what I like about this site/forum, you post a question, it gets a handful of views and within a week people are jumping in and helping out .
__________________
gee dub
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:17.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
© www.GermanLook.net 2002-2017. All Rights Reserved