#1
|
|||
|
|||
Oilcooler
Were do you guys mount your external oilcoolers? Front of the car or above the transmission? I'm just concern about oil pressure. May loose oil pressure if the lines are long to the front apron?
__________________
T4 2666 1303s |
#2
|
||||
|
||||
most locate it under the package tray, above or slightly to the side of the tranny. mine hangs about 6 inches under the tray (due to the cup brace) and to the left of the tranny. fan on bottom and pulls through. my cooling has been almost too good. i run a DTM so i have a stock cooler and the external which is a Setrab. i have yet to get it above 205.
__________________
zen '73 2316 TIV GL Standard Bug (quasi) Company Branding, Graphic Design, and Web Services at DigiVinci Design |
#3
|
||||
|
||||
Speaking of Oil Coolers..
Im loooking to Go Full Flow.. This Is the Kit I found.. http://thesamba.com/vw/classifieds/detail.php?id=141575 I heard a RX-7 R1 Cooler Will Fit¿ What Do you think of Tapping the case Without splitting it¿ Thanks Troy
__________________
SOLD!! 65 Bug 1835cc,Duel Dell 34's,BMD Serp Belt, A1 Perf. Sidewinder,CompeUfire Pointless Ign 95A Alt,CSP Valve Covers,Randar Diego 16's Soon [URL=http://www.cardomain.com/id/troy_audio] |
#4
|
||||
|
||||
I did a tech article on the RX7 cooler, it is in the Tech Article on the main page.
I have seen the case taped for full flow withoput spitting the case by hand drilling and tapping the case useing grease in the bit and tap to hold the chips.
__________________
NO_H2O 72 1302 Smack Black GL 73 Bus (2L CIS Powered) 66 Beetle, 73 Standard Beetle 72 Pinzgauer 710M Volksport Kafer Gruppe |
#5
|
|||
|
|||
How about guys using oilcoolers at the front or a combination of those remmele type scoups directing air to the oilcoolers then coming out to the rear wheel area.
__________________
T4 2666 1303s |
#6
|
||||
|
||||
I plan to move mine to the front when I do the 901 trans install. I will plumb it with hard lines the length of the car and short flex lines at the cooler and engine.
__________________
NO_H2O 72 1302 Smack Black GL 73 Bus (2L CIS Powered) 66 Beetle, 73 Standard Beetle 72 Pinzgauer 710M Volksport Kafer Gruppe |
#7
|
||||
|
||||
where did you get those "muffin fans" that you used in the tech article?
__________________
www.subynotch.com |
#8
|
||||
|
||||
I picked them up from www.partsexpress.com they are ball bearing/110 cfm ea.
__________________
NO_H2O 72 1302 Smack Black GL 73 Bus (2L CIS Powered) 66 Beetle, 73 Standard Beetle 72 Pinzgauer 710M Volksport Kafer Gruppe |
#9
|
||||
|
||||
Oil cooler up front is fine for pressure. I even use the stock (old) oil pump and presuure is fine. Oil never gets above 185F in my 2.4 ltr with 10.8 CR
In my late 03 it sits behind the original a/c grille. |
#10
|
|||
|
|||
Any idea what diameter your oil lines are Wally?
I'm looking to mount my cooler up front, but have heard it mentioned several times that too large a diameter can cause issues with pressure drop. |
#11
|
||||
|
||||
I (and many, many others) have the (sort of standard) 1/2" inner diameter oil lines.
A new 30mm pump would be better of course |
#12
|
|||
|
|||
Thanks guys for the input, one for the front and one for the rear! Going to run 2.7 T4.
__________________
T4 2666 1303s |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|