GermanLook Forums  

Go Back   GermanLook Forums > General > Project Builds

Reply
 
Thread Tools Display Modes
  #46  
Old June 18th 2018, 18:13
owdlvr's Avatar
owdlvr owdlvr is offline
Registered User
 
Join Date: Sep 2008
Location: Canada - West Coast
Posts: 704
I've actually got a set of 944 Alloy arms, so I wouldn't need yours in trade. We can definitely work out something for my steel ones.
__________________
--
'71 Type 1 - Rally Project
'58 Type 1 - I bought an early...
'75 Type 1 - Family Heirloom
'93 Chevy 3500 pickup - Cummins Swap
Reply With Quote
  #47  
Old June 20th 2018, 08:36
H2OSB H2OSB is offline
Registered User
 
Join Date: Jan 2003
Location: Modesto, CA
Posts: 131
Errg! I really just wanted to get rid of those alloy trailing arms. Ok, when you get to the point where your steel arms have become free (of the car), let me know.
__________________
johnL (aka H2OSB)
'74 1303, Outlaw sedan (with a GL flavor)
www.superbeetlesonly.com
Reply With Quote
  #48  
Old June 20th 2018, 16:30
owdlvr's Avatar
owdlvr owdlvr is offline
Registered User
 
Join Date: Sep 2008
Location: Canada - West Coast
Posts: 704
So I pulled the car out onto the driveway to blast and grind any areas where I suspect there would be rust I need to deal with. At this stage I’ve only done the outside bits, and at times I’m quite excited about not finding a horror story, and other times I’m like “ugh, not as good as I hoped”. Don’t get me wrong, this is much better than the other cars I’ve looked at, but not as good as I initially thought. On the plus side, the C-Pillars are no surprise. I bought the car knowing that they were going to be a problem.


Easy fix, no welding required…






Couldn’t blast in here with my quick setup, but I also have a whole second replacement section so the rust isn’t a problem.








This area was a bit of a surprise. It looked very minor with the black paint over it, but once I started blasting the glass went right through it.


I knew about the bits above the trim line…but the rot continues down below.


I see major surgery in my future :P


In general, I haven’t seen late model cars rot so close to the rain gutter, without showing rot higher up. I’m not sure how deep into this C pillar I need, or want, to cut into …but I think after fixing the passenger side I’ll have a good handle on how much to open it up.


This will be an easy fix.


I think this heater channel will end up being a patch job, not a full channel.

Doesn’t look like I took photos of the rear apron, but it’s a 50/50 mix of cheer and disappointment. The apron is straight and sold, but the area covered by the deck lid has some very rough surface rust pitting. I will see what can be done to fix it, but I might be looking for a new apron to graft in. Haven’t touched any of the interior rust, which is mostly in the C-Pillar or luggage tray. Will fix the outside first, and then worry about the inside of the car. Also haven’t looked too hard at the usual rust in front of the dash, as I’m not sure how much of the factory dash I’m keeping.

-Dave
__________________
--
'71 Type 1 - Rally Project
'58 Type 1 - I bought an early...
'75 Type 1 - Family Heirloom
'93 Chevy 3500 pickup - Cummins Swap
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 17:48.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
© www.GermanLook.net 2002-2017. All Rights Reserved