#1
|
||||
|
||||
No Oil Pressor...
Hey ..
Iv just had my motor running long enuff to check the guages.. Fuel Press is holding at: 4.6lbs Oil: -N/A- My Guage has power & the sender wire is hooked up.. Maybe bad new sencer? Things Im Checking on.. Pull Valve Cover To see if it has oil.. Recheck sender & wires.. What all can you think of.. the motor ran fin before the overhall. I changed the valve covers,header/exhaust,Carbs,fan,alt,tins,wiring ign system,fuel system,pully system >>1st Time Running Video<< Thanks N Advance Peace Troy
__________________
SOLD!! 65 Bug 1835cc,Duel Dell 34's,BMD Serp Belt, A1 Perf. Sidewinder,CompeUfire Pointless Ign 95A Alt,CSP Valve Covers,Randar Diego 16's Soon [URL=http://www.cardomain.com/id/troy_audio] |
#2
|
||||
|
||||
for your oil pressure gauge, are you useing a special sender or the stock sender? The stock sender isn't made for a gauge, only to make a light in the dash go out when there is pressure, Just to be courius, is the engine/transmission grounded to the frame?
__________________
Mike '04 R32 Tornado Red '02 New Beetle TDI - Daily driver '64 Ghia - Project!!-Subaru EJ20T, MS/EDIS, 993 brakes, 914 Tranny... |
#3
|
||||
|
||||
I checked the covers..
they had oil in'em i found a small leak by the oil fill/breather Bottom edge leaks(Drip drip drip) 6" marking over night I will check into my wiring & sender when I get back toit Peace VDubz 4 Life c(<>_<>)0 |,,|_
__________________
SOLD!! 65 Bug 1835cc,Duel Dell 34's,BMD Serp Belt, A1 Perf. Sidewinder,CompeUfire Pointless Ign 95A Alt,CSP Valve Covers,Randar Diego 16's Soon [URL=http://www.cardomain.com/id/troy_audio] |
#4
|
||||
|
||||
I just looked i dont see a ground strap on the block.. but Maybe on the tranz.. Need to jack it up..
__________________
SOLD!! 65 Bug 1835cc,Duel Dell 34's,BMD Serp Belt, A1 Perf. Sidewinder,CompeUfire Pointless Ign 95A Alt,CSP Valve Covers,Randar Diego 16's Soon [URL=http://www.cardomain.com/id/troy_audio] |
#5
|
||||
|
||||
if you're using solid mounts or you didn't take the tranny out, it should be there.
__________________
Mike '04 R32 Tornado Red '02 New Beetle TDI - Daily driver '64 Ghia - Project!!-Subaru EJ20T, MS/EDIS, 993 brakes, 914 Tranny... |
#6
|
|||
|
|||
if your running a full flow setup try taking the line off the pump cover, pour some oil down it, then try starting it. mine doesn't like to prime after a build and that always works for me. btw- leave the line hooked to the pump cover itself, unhook it from the other end
|
#7
|
||||
|
||||
Im not full flow yet..
But i will keep that inmind for after I do.. Iv been looking for leaks & found a few.. Dip-Stick,Alt Stand,Filler/breather on the mounting spot.. I think (As stated)My Oil Press maybe for a Light only.. But its running ok for now.. lil timming & carb tuning then i should be ok.. Peace Troy
__________________
SOLD!! 65 Bug 1835cc,Duel Dell 34's,BMD Serp Belt, A1 Perf. Sidewinder,CompeUfire Pointless Ign 95A Alt,CSP Valve Covers,Randar Diego 16's Soon [URL=http://www.cardomain.com/id/troy_audio] |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|